🧰 Pro AV Rack Solutions

This article explains how to use InterScribe features effectively in your events.

  • Actualizado el 10 nov 2026
  • 3 min de lectura
  • Para: organizadores

Esta página aún no está traducida al español. Estás leyendo la versión en inglés.

Overview

For large-scale events, multi-room facilities, or broadcast setups, you can integrate InterScribe into your existing AV infrastructure using a dedicated rack system. These systems run InterScribe agents on rack-mounted mini PCs or embedded Linux devices, with audio routed via Dante, NDI, or analog interfaces. This approach centralizes audio management while supporting high-quality, multi-channel streaming.


🪜 Step‑by‑Step Instructions

  1. Plan your architecture

    • Determine the number of rooms and languages you’ll support.

    • Each simultaneous language or room requires a unique AV Channel in InterScribe .

    • Choose your integration method:

      • Dante or NDI for IP-based digital routing
      • Analog for simpler setups
  2. Select rack hardware

    • Use rack-mounted mini PCs or embedded Linux devices (e.g., Intel NUCs).

    • Each device should run the Desktop Streamer Agent and have:

      • SSD storage
      • 4–8 GB RAM
      • Wired gigabit Ethernet
    • Pair with audio interfaces suited to your transport:

      • Dante/NDI card
      • AES67 interface
      • Multi-channel USB interface
  3. Configure network audio routing

    • For Dante:

      • Connect mixers/mics via Dante-enabled stage boxes or adapters
      • Use Dante Controller to route channels to the Dante Virtual Soundcard on the mini PC
    • For NDI:

      • Send audio via NDI encoders (e.g., BirdDog, Kiloview)
      • Install NDI Tools and select the NDI source in the Desktop Agent
  4. Install and configure InterScribe Desktop Agent

    • Install the agent on each rack PC
    • Assign a unique AV Channel to each device in InterScribe
    • Select the correct input device (Dante, NDI, or USB) and verify audio levels
  5. Connect to your mixing console

    • Use aux sends or matrix outputs to create clean, pre-mixed feeds for each language
    • Avoid sending ambient mics unless needed
    • Clearly label cables and ports for quick identification
  6. Monitor and manage

    • Use the Monitor Dashboard in InterScribe to track agent status and AV Channel activity
    • Keep redundant gear on hand (e.g., spare mini PC, audio interface)
    • Test failover workflows ahead of any major event

✅ Tips & Best Practices

  • Redundancy: Use backup power and network paths for critical systems
  • Latency: Balance buffer size vs delay for Dante/NDI; avoid Wi-Fi for agents
  • Cooling & cable management: Keep racks ventilated and clearly routed
  • Document everything: Maintain an audio routing map and agent assignments

🖼️ Visual Aids

📸 Diagram – Rack Integration Diagram showing mini PCs connected to Dante/NDI network with separate AV channels feeding InterScribe

📸 Photo – Pro AV Rack Rack with mini PCs, audio interfaces, and networking equipment


🛠 Troubleshooting / FAQs

IssueCauseSolution
Dropouts or lagNetwork congestion or low bufferUse isolated AV networks and increase Dante/NDI buffer size
Wrong audio source in sessionMisassigned AV ChannelCheck agent configuration and AV Channel selected in event
Buzz/hum in analog feedGround loop or interferenceUse balanced connections and DI boxes; common ground preferred
Agent offlineHardware or service failureSwap to spare device and set up monitoring for alerts

ℹ️ Note: This is a high-level guide. For wiring diagrams, licensing, or vendor-specific config (e.g., Shure, Allen & Heath, Yamaha), consult AV documentation or hire a certified integrator.


¿Esta página resolvió tu problema?

Tu respuesta llega directamente a quienes escriben estas páginas.

Hacer la prueba

We respect your privacy.

We use cookies for language, theme and to measure visits so we can improve the site. You can turn measuring off in one click. Learn more ·